South metro
Sub-Zero repair in Lone Tree
Most of the kitchens here were drawn after the appliances were chosen. The refrigeration is flush with the run and faced in the same joinery, so from the doorway it reads as cupboard doors.
What the kitchens here do to a built-in
- Columns faced in cabinet panels
- A wooden front weighs more than a steel one, so a hinge or a closer that has begun to give shows first as a door standing a hair proud.
- Cabinets fitted tight into the run
- All the air the machine gets arrives through the grille, so a filler strip pushed home too far or a basket left against it changes how hard it works.
- Everything set flush and level
- When a cabinet settles even slightly the joinery shows it, and a door catching its frame is usually the first sign anything has moved.
Doorways in these houses are wide and the garage is usually a few steps from the kitchen, so the journey is not the difficulty. Getting a panel off and back unmarked is.
What a matching front hides
A stainless door tells on itself. When a seal stops pulling tight the gap shows, and so does the line of the door against its frame. A front cut from the same oak as the cupboard beside it gives nothing away. So in a kitchen fitted like this, a seal is usually caught by something other than the eye: butter softer than it ought to be at one end of a shelf, a corner of the compartment running warmer than the rest, a door that has stopped thumping home the way it used to.
None of that needs a tool. What it needs is somebody noticing, and then saying it precisely. Which door, which corner, and whether it began after the joinery was worked on. A cabinet that went in square and is not square now has either been moved or has settled, and what that asks for is an adjustment rather than a part.
What we handle in Lone Tree
- Refrigerator Repair Diagnosis and repair of Sub-Zero built-in refrigerators, integrated columns and undercounter units.
- Freezer Repair Frost build-up, failed defrost parts and temperature drift on Sub-Zero freezers and freezer drawers.
- Ice Maker Repair Clear-ice modules, inlet valves and drains on Sub-Zero ice makers, including undercounter machines.
- Wine Cooler Repair Zone temperature control, seals and compressor work on Sub-Zero wine storage units and columns.
If you cannot tell yet which of the four it is, start from what the cabinet is doing instead — that is the page this site is built around.
Asked about Lone Tree
Does a cabinet panel change what can be repaired?
Hardly at all. The grille, the door seal, the controls and the machine compartment are all reachable with the front where it is, and a panel comes off only when the door itself has to. Say it is a panel front at the booking and the day is planned for it.
The drain at the back is blocked. Can we clear it ourselves?
On the built-in and integrated cabinets in most of these kitchens, no. Sub-Zero says a clogged drain tube on those has to be cleared on a service visit, and nothing should be pushed into it meanwhile. Ring Sub-Zero Appliance Repair Denver on (303) 729-0972.
Reviews
Reviewed by Lone Tree owners
5.0/ 5652 reviews
Ice built into a sheet across the back of the freezer, which is odd in air this dry. Failed defrost heater. He replaced it, cleared the drain, and explained why the frost comes back if it clogs.
Delaney H.Cherry Creek
The undercounter wine unit in our basement bar hummed loud enough to hear upstairs. Not the compressor, as another shop insisted, but loose mounts and a rattling back panel. Re-seated, and it is quiet.
Harvey T.Washington Park
Puddle on the floor of our 1920s apartment kitchen every morning. The drain line under the ice maker had come loose behind the cabinet. He re-seated and clamped it, then checked the floor for damage.
Romy H.Capitol Hill
Talk to someone
A Sub-Zero problem in Lone Tree?
Name the model and say what changed, and the technician arrives carrying what that fault usually needs. Technicians work 8:00 am to 8:00 pm, any day of the week, and the line takes a call 24/7.